Led Strips 10 M

Led Strips 10 M

Led Strips 10 M

There are 30 RGB LEDs per meter, and you can control each LED individually! Yes, that's right, this is the digitally-addressable type of LED strip. You can set the color of each LED's red, green and blue component with 8-bit PWM precision (so 24-bit color per pixel). The LEDs are controlled by shift-registers that are chained up down the strip so you can shorten or lengthen the strip. Only 1 digital output pin are required to send data down. The PWM is built into each LED-chip so once you set the color you can stop talking to the strip and it will continue to PWM all the LEDs for youThe strip is made of flexible PCB material, and comes with a weatherproof sheathing. You can cut this stuff pretty easily with wire cutters, there are cut-lines every 1.3″/3.4cm (1 LED each). Solder to the 0.1″ copper pads and you're good to go. Of course, you can also connect strips together to make them longer, just watch how much current you need! We have a 5V/2A supply that should be able to drive 1 meter and a 5V/10A supply that can drive up to 10 meters (depending on use) You must use a 5V DC power supply to power these strips, do not use higher than 6V or you can destroy the entire stripAs of May 20, 2014 these come in 5 meter reels with a 2 or 3-pin JST SM connector on each end and separated power/ground wires. These strips are sold by the meter! If you buy 5 meters at a time, you'll get full reels with two connectors. If you buy less than 5m, you'll get a single strip, but it will be a cut piece from a reel which may or may not have a connector on it. If the piece comes from the end of the reel, the connector may be on the output end of the strip!To wire up these strips we suggest picking up some JST SM plug and receptacle cables. You'll want one of each, one wire is for ground the other is for signal. For the power wire, you will also probably want a 2.1mm DC jack to wire in so you can connect one of our wall adapters to power it.Our detailed NeoPixel Uberguide has everything you need to use NeoPixels in any shape and size. Including ready-to-go library & example code for the Arduino UNO/Duemilanove/Diecimila, Flora/Micro/Leonardo, Trinket/Gemma, Arduino Due & Arduino Mega/ADK (all versions)
led strips 10 m 1

Led Strips 10 M

Connect the input of the RGB led Strip Amplifier and RGB led strip light, at the same time you need to use another power supply to connect the led strip amplifier. If you want to connect more led strip lights, you can choose LED Splitter to connect.
led strips 10 m 2

Led Strips 10 M

·【Upgraded Materials】: Using upgraded adhesive 3M backing, super viscosity and easy installation. Double layer copper, twice costs than other single layer copper LED strips in the market.
led strips 10 m 3

Led Strips 10 M

32ft about solid one length. If you cut, you can only power one length that was cut. Remember. This strip is once piece 32ft long, if you cut it anywhere, the other protion requires another controller box. We do sell these controller boxes under LED strips. You cannot operate a cut peice without a RGB controller box.
led strips 10 m 4

Led Strips 10 M

Very clever, thank you for sharing this solution.

Led Strips 10 M

Any other problems about LED Lighting, you also can ask us, and we will help you to solve it.More Comments
led strips 10 m 5

Led Strips 10 M

Very clever, thank you for sharing this solution.

Led Strips 10 M

Any other problems about LED Lighting, you also can ask us, and we will help you to solve it.

Published on Mar 8, 2017 | Under News | By admin
please edit your menu